MATERIAL SAFETY DATA SHEET
Finished Polyurethane Elastomer Article
ISSUED: June 30, 2020
I – IDENTIFICATION |
|
|
PRODUCT (TRADE) NAME |
linel® spandex |
|
GENERAL CHEMICAL DESCRIPTION |
Cured Polyurethane Elastomer |
|
INTENDED USE |
Textiles – Hygienic – Technical |
|
COMPANY NAME |
PT. FILLATTICE Indah Industry Jl. Pajajaran 14 No. 62, Gandasari, Jatiuwung, Tangerang 15137, INDONESIA |
|
TELEPHONE NUMBER |
+62 (021) 55657000 |
|
FAX NUMBER |
+62 (021) 55655336 |
|
URL |
www.linel-tape.com |
II – INGREDIENTS |
|
|
COMPOSITION |
Polyurethane solid with polyol, di-isocyanate, additives, fillers, added to obtain specific material properties |
III – PHYSICAL AND CHEMICAL PROPERTIES |
|
|
APPERANCE |
Solid |
|
PERCENT VOLATILES |
None |
|
MELTING POINT |
N/A |
|
SOLUBILITY IN WATER |
Insoluble |
|
SPECIFIC GRAVITY |
0.97 – 1.1 |
IV – STABILITY AND REACTIVITY |
|
|
STABILITY |
Stable at ambient temperatures and pressures |
|
CONDITIONS TO AVOID |
None known |
V – EXPOSURE CONTROLS/PERSONAL PROTECTION |
|
|
VENTILATION |
Local exhaust at processing equipment. Grinding and machining of parts should be reviewed to assure that particulate levels are kept below recommended standards. |
|
PROTECTIVE EQUIPMENT SKIN |
Protective gloves, long sleeve cotton shirt and long pants are required when handling molten material. |
|
EYE |
Safety glasses are recommended to prevent particulate from entering eyes while grinding or machining. |
|
RESPIRATOR |
None under normal processing, if ventilation is adequate (Grinding and machining of parts should be reviewed to assure that particulate levels are kept below recommended standards). |
Potential environmental effects
Aquatic toxicity: There is a high probability that the product is not acutely harmful to aquatic organisms.
VI – HEALTH HAZARDS IDENTIFICATION |
|
|
ACUTE OR IMMEDIATE EFFECTS SKIN |
Molten material may cause thermal burns. |
|
INHALATION |
Shapes/Solids are not considered an inhalation hazard. |
|
INGESTION |
Not a probable route of exposure. |
|
LONG TERM DELAYED EFFECTS |
None known |
|
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE |
None known |
|
CHRONIC EFFECTS |
No known chronic affects. As with most high molecular weight polymer, this material is considered inert. |
VII – FIRST AID MEASURES |
|
|
FLASH POINT |
Not Applicable |
|
FLAMMABLE LIMITS |
Not Applicable |
|
SELF-IGNITION TEMPERATURE |
Not self-igniting |
|
EXTINGUISHING MEDIA |
Carbon Dioxide, Water spray, Dry Chemical, Foam. |
|
UNUSUAL FIRE OR EXPLOSION HAZARDS |
POLYURETHANE ELASTOMER will ignite and burn when exposed to flames. Fumes and dense, irritating smoke may be evolved upon exposure to heat or open flame. |
|
SPECIAL FIRE FIGHTING PROCEDURES |
Firefighters should wear self-contained breathing apparatus and turn-out gear. |
|
SKIN |
If molten polymer contacts skin, cool rapidly with cold water. Do not attempt to peel polymer from skin. Obtain medical attention for thermal burns. |
|
EYE |
In case of eye contact, immediately flush eyes with plenty of water for at least 15 minutes. Consult a physician if symptoms persist. |
|
INHALATION |
If exposure to fumes from overheating, move to fresh air. |
VIII- TOXICOLOGICAL INFORMATION |
|
|
CHRONIC TOXICITY |
Harmless |
|
MEDICAL CONDITIONS PRONE TO AGGRAVATION BY EXPOSURE |
No information available |
IX – FIRE FIGHTING MEASURES |
|
|
AUTOIGNITION TEMPERATURE |
N/A |
| HAZARDOUS PRODUCTS OF COMBUSTION |
Oxides of carbon, water and smoke under burning conditions. Other combustion products are hydrogen cyanide, aromatic and aliphatic hydrocarbons. |
X – ACCIDENTAL RELEASE MEASURES |
|
|
SPILL OR RELEASE |
N/A |
XI – HANDLING AND STORAGE |
|
|
HANDLING |
Open containers only in well-ventilated area. |
|
STORAGE |
Store away from sources of direct heat. |
XII – DISPOSAL CONSIDERATIONS |
|
|
DISPOSAL |
Treatment and disposal must be in accordance with federal, state, provincial and local regulations. |
HMIS III Rating
Health: 1
Flammability: 1
Physical Hazard: 0
DISCLAIMER OF EXPRESSED AND IMPLIED WARRANTIES
The information presented in the Material Safety Data Sheet is based on data believed to be accurate as of the date this Material Safety Data Sheet was prepared. HOW EVER, NO WARRANTY OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR ANY OTHER WARRANTY IS EXPRESSED OR IS TO BE IMPLIED REGARDING THE ACCURACY OR COMPLETENESS OF THE INFORMATION PROVIDED ABOVE, THE RESULTS TO BE OBTAINED FROM THE USE OF THIS INFORMATION OR THE PRODUCT, THE SAFETY OF THIS PRODUCT, OR THE HAZARDS RELATED TO ITS USE. No responsibility is assumed for any damage or injury resulting from abnormal use or from any failure to adhere to recommended practices.
The information provided above, and the product, are furnished on the condition that the person receiving them shall make their own determination as to the suitability of the product for their particular purpose and on the condition that they assume the risk of their use. In addition, no authorization is given nor implied to practice any patented invention without a license.
JI. Pajajaran N°62, Gandasari, Jati Uwung, Tangerang 15137, Indonesia
